GLOBAL BEST DAEKWANG
SDL1000X/SDL1000X-E series Programmable DC Electronic Load has a 3.5 inch TFT-LCD display, a user-friendly interface and superb performance specifications. The SDL1020X/SDL1020X-E models feature an input range of 150 V/30 A 200 W while the SDL1030X/SDL1030X-E have an input range of 150 V/30 A 300 W. The SDL1000X series leads with measurement resolution of 0.1 mV/0.1 mA and the base SDL1000X-E series resolution is 1 mV/1 mA and adjustable current rise times from 0.001 A/μs~2.5 A/μs. For remote communication and control, the SDL series includes RS232/USB/LAN interface types. The SDL1000X series delivers stability over a wide range of applications and can meet all kinds of testing requirements. including: Power, battery/handheld device design, industry, LED lighting, automotive electronics, and aerospace.
Key Features
• SDL1020X/SDL1020X-E (Single channel ): DC 150 V/30 A, total power up to 200 W
• SDL1030X/SDL1030X-E (Single channel ): DC 150 V/30 A, total power up to 300 W
• 4 static modes / Dynamic mode: CC/CV/CR/CP
• CC Dynamic mode: Continuous, pulsed, toggled
• CC Dynamic mode: 25 kHz, CP Dynamic mode: 12.5 kHz, CV Dynamic mode: 0.5 Hz
• Measuring speed of voltage and current: up to 500 kHz
• Adjustable current rise time range: 0.001 A/us~2.5 A/us
• Min. readback resolution: 0.1 mV, 0.1 mA
• Short-circuit, Battery test, CR-LED mode, and factory test functions
• 4-wire SENSE compensation mode function
• List function supports editing as many as 100 steps
• Program function supports 50 groups of steps
• OCP, OVP, OPP, OTP and LRV protection
• External analog control
• Voltage, Current monitoring via 0-10 V
• 3.5 inch TFT-LCD display, capable of displaying multiple parameters and statessimultaneously
• Built-in RS232/USB/LAN communication interface, USBGPIB module (optional)
• Waveform trend chart and easy-touse file storage and call functions
• Includes PC software: Supports SCPI, LabView driver
Characteristics
Steady state operating mode |
| Dynamic test mode up to 25 kHz (CC) |
The SDL features four operating modes to provide flexible test capabilities. In CC mode, the electronic load will sink a constant current, regardless of the voltage at its terminals. In CV mode, the electronic load will cause a constant voltage to appear at its terminals. In CR mode, the electronic load will behave as a fxed resistance value. As shown in the figure, the electronic load will linearly change the current according to the input voltage. In CP mode, the electronic load will cause a constant power to be dissipated in the load. | The transient test allows switching between two different load values. A common application is to test the dynamic characteristics of a DC source or DUT (Device-Under- Test). The transient test function enables the load to periodically switch between two set levels (Level A and Level B). The highest frequency can be set to 25 kHz in CC mode. The highest frequency can be set to 12.5 kHz in CP modes. |
4-wire SENSE compensation mode function | |||||||||||||
In CC/CV/CR/CW mode, when a load is connected to a power supply, it will cause a large voltage drop on the connection lines between tested instrument and terminals of load. Using remote sense, you can measure the voltage at the DUTs input terminals, effectively removing the additional error due to the voltage drop in the connection wires.
CR-LED Mode The SDL1000X includes a CR-LED mode specifcally for LED driver testing. Basing on the traditional CR mode, CR-LED mode adds a diode breakover voltage setting. When the input voltage is above this set value, the DC load start to work. Thus, it can emulate the actual characteristics of an LED.
![]() OCPT/OPPT Mode
Over-current protection (OCPT) mode prevents drawing too much current from the DUT. After the input voltage reaches the Von point, the DC load will start to draw a current from the source after a delay time. The current value will increase by a certain step size at regular intervals. Simultaneously, the DC load will compare the input voltage to the OCP voltage:If it is lower, then the present current value will be compared to see if it is in the current range you have set. Within the range, the OCP test will evaluate Pass or Fail. If it is outside of the set range, the DC load will to increase drawing current and compare the voltage again.
![]() Voltage Rise/Fall speed test The electronic load is also equipped to directly measure voltage rise and fall times. It can calculate the time from one voltage to another without the need for additional measurement instrumentation. With an SDL1000X, you can save money and improve effciency.
![]() Voltage threshold function The SDL1000X can be set to turn on or off if the input voltage is at, above, or below a set value. By defning these thresholds, you control when the load is active. Which minimizes test time and increases safety.
![]() Waveform trend chart function The electronic load includes a waveform display function and supports the following operations for the waveform: Pause, recording, and capturing the waveform. You can quickly observe the trends of parameter changes as they occur throughout the test.
![]()
Save/Recall setting parameters The load allows you to save different types of fles to the internal and external memories. You can recall and read them when necessary.
![]() External analog control The load allows the user to control current or voltage through external analog terminals (EXT PRG). Input a 0-10 V analog to adjust 0-100% rated voltage and current. It is very useful for those applications that need to change the input value with external signals.
Multiple policy protection modes The SDL1000X series Programmable DC Electronic Load provides five protection types: OVP, OCP, OPP, OTP and LRV. When OVP/OCP/OPP/OTP/reverse voltage protection (LRV) occurs, the load will immediately turn off the input and stop sinking. Then, a prompt message is displayed.
|
Spec Comparison
Model |
Min. readback resolution |
Display |
Current Slew Rate |
Measuring speed |
CC Dynamic mode frequency |
Mode |
Input power |
Input current |
Input voltage |
SDL1020X |
0.1 mV, 0.1 mA |
3.5 inch TFT-LCD display |
0.001 A/us~2.5 A/us |
up to 500 kHz |
25 kHz |
CC/CV/CR/CP |
200 W |
30 A |
150 V |
SDL1020X-E |
1 mV, 1 mA |
3.5 inch TFT-LCD display |
0.001 A/us~2.5 A/us |
up to 500 kHz |
25 kHz |
CC/CV/CR/CP |
200 W |
30 A |
150 V |
SDL1030X |
0.1 mV, 0.1 mA |
3.5 inch TFT-LCD display |
0.001 A/us~2.5 A/us |
up to 500 kHz |
25 kHz |
CC/CV/CR/CP |
300 W |
30 A |
150 V |
SDL1030X-E |
1 mV, 1 mA |
3.5 inch TFT-LCD display |
0.001 A/us~2.5 A/us |
up to 500 kHz |
25 kHz |
CC/CV/CR/CP |
300 W |
30 A |
150 V |
Lineup
SDL1020X | 150 V/30 A 200 W Programmable DC Electronic Load |
SDL1020X-E | 150 V/30 A 200 W Programmable DC Electronic Load |
SDL1030X | 150 V/30 A 300 W Programmable DC Electronic Load |
SDL1030X-E | 150 V/30 A 300 W Programmable DC Electronic Load |
Ordering Information
Contents
• SDL1030X Programmable DC Electronic Load
• USB Cable
• Quick Start Guide
• Calibration Certifcate
• Power cord
Product information | Product No |
150 V/30 A 200 W Programmable DC Electronic Load | SDL1020X/SDL1020X-E |
150 V/30 A 300 W Programmable DC Electronic Load | SDL1030X/SDL1030X-E |
Standard Accessories | |
USB Cable -1 | |
Quick Start -1 | |
Calibration Certificate -1 | |
Power cord -1 |
※ 자세한 사항은 'DataSheet'나 'Manual'을 참조해 주세요.
품명 및 모델명 | 상품상세정보 참조 | 허가 관련 | 상품상세정보 참조 |
---|---|---|---|
제조국 또는 원산지 | 상품상세정보 참조 | 제조자/수입자 | 상품상세정보 참조 |
A/S 관련 연락처 | 02-2617-0787 |
- 배송비 : 기본배송료는 3,000원 (제주도 및 일부 도서산간 지역은 배송비가 추가됩니다.)
\200,000원 이상 구매시 무료배송
- 오후 5시 이전 주문시 통상적으로 당일 발송
- 제품 품절인 경우가 있기 때문에 납기일 확인 후 주문 부탁드립니다.
- 배송예정일은 주문시점(주문순서)에 따른 유동성이 발생하므로 평균 배송일과는 차이가 발생할 수 있습니다.
- 본 상품의 배송 가능일은 결제완료 된 날로부터 2~3 영업일입니다. 배송 가능일이란 본 상품을 주문 하신 고객님들께 상품 배송이 가능한 기간을 의미합니다.
교환 & 반품안내
- 특수 제품, 주문 제품 등의 경우, 그 특성상 주문이 접수된 후 취소 및 환불이 불가합니다. 주문 전 충분히 상담하신 후 구매해 주세요.
(특수 제품이란, 보유제품이 아닌 주문 후 생산하며 출고하는 제품을 말합니다.)
- 제품 특성상 주문이 접수된 후 단순 변심에 의한 취소 및 환불은 당일에 한해 가능합니다. (취소및 환불 접수전 반드시 고객센터를 통해 연락바랍니다.)
- 전자 제품 특성상 제품포장 개봉 후에는 교환 및 환불이 불가능합니다. (제품 하자 제외)
- 모든 교환·반품은 수령 후 7일 이내 접수되어야 하며, 접수 전에 고객센터로 문의해 주셔야 진행이 가능합니다.
- 미개봉 제품의 경우, 받으신 날로부터 7일 이내 접수하시면 교환이 가능합니다.
- 개봉하신 제품은 7일 이내라도 교환이 불가합니다.(제품 하자 제외)
- 배송된 날로부터 7일이 지나면 어떤 교환·반품도 불가하므로 받으시면 제품 상태를 꼭 확인해 주세요. (제품 하자 포함)
- 소비자 변심에 의한 교환은 왕복 운임을 부담하셔야 합니다.
환불안내
- 상품 청약철회 가능기간은 상품 수령일로 부터 7일 이내 입니다.
- 주문 제품, 특수 제품의 경우 교환/반품이 불가합니다.
- 주문 전 충분한 상담을 하신 후, 신중히 구매해 주세요.
- 환불신청시 왕복 운송료를 부담하셔야 합니다.
AS안내
소비자분쟁해결 기준(공정거래위원회 고시)에 따라 피해를 보상받을 수 있습니다.
:: A/S 처리 문의 ::
전화 : 02) 2617-0787
E-MAIL : kdk@kdk.co.kr
⊙ A/S처리기간은 5일~4주 정도로, 제품에 따라 상이합니다.
⊙ 무상보증수리 : 제조사의 품질보증 기간에 따라 다릅니다. 무상보증 수리기간은 일반적으로 1년, 3년입니다.
무상보증수리를 위한 왕복 배송료는 대광계측기(주)에서 부담합니다.
단, 무상보증기간일지라도 소모품 교체나 소비자 과실일 경우 비용이 추가될 수 있습니다.
⊙ 유상수리 : 무상보증 기간이 지난 제품에 이상이 생겼을 경우에는 유상수리를 하셔야 합니다.
기본적으로, 수리를 위해 대광계측기(주)로 보내시는 배송료는 고객 부담, 받으시는 배송료는 대광계측기(주)에서 부담합니다.
타사에서 구입한 제품도 대광계측기(주)에서 수리 가능합니다.
상품이 장바구니에 담겼습니다.
바로 확인하시겠습니까?
상품이 찜 리스트에 담겼습니다.
바로 확인하시겠습니까?